# How to Fill Holes Around a House Foundation?

21 min read · Updated October 2026 · By Ricardo Chamorro · ICC-certified Residential Building Contractor

FOUR THINGS THAT MAKE HOLES BESIDE A SLAB. NAME YOURS BEFORE YOU FILL IT.

WATER

Erosion

Water carved the soil away, usually a downspout, a roof valley, or runoff funneling along the slab. Reroute the water first or the hole returns.

CLAY

Shrinkage gap

Clay pulled back from the slab edge in dry weather. Seasonal. Steady moisture closes it back up.

CRITTER

Animal burrow

Armadillos, rats, gophers and fire ants all dig beside slabs, and the size of the hole usually names the digger. Fill and compact after the tenant is gone.

TRENCH

Trench settlement

The soil over a buried utility or plumbing line settled. Fill it, but watch it, because a leak underneath makes the same shape.

The fill job is the easy part. Naming the cause is what keeps the hole from coming back.

How to fill holes around a house foundation? Figure out what made the hole, then fill it with a clayey soil, packed in thin layers, and finish with a grade that sends water away from the slab. Skip sand and gravel next to the foundation, and skip the temptation to just rake loose dirt into the void. If water carved the hole, fix the water first or you will fill the same hole every year. And if the ground is opening up because the house itself is moving, filling is the wrong job entirely. Here is how to tell the difference, and how to do the fill right when it really is just a hole.

Clay pulled back from a slab edge in dry weather. This gap is seasonal shrinkage, and it calls for steady moisture, not a bag of sand.

## Name the cause before you touch a shovel

Around Central Texas slabs, holes and low spots come from four places. Erosion is the big one, whether from a downspout dumping at a corner, a roof valley concentrating rain onto one patch of dirt, or runoff cutting a channel along the slab edge. The water carries soil away a little at a time until one day there is a trench where the flower bed was. Second is the seasonal shrinkage gap, which is not erosion at all. Our clay swells when wet and shrinks when dry, and in a hard August it pulls back from the slab edge and opens a crack you can slide your hand into. Third, animals. Loose, sheltered soil beside a slab is prime real estate for rodents and armadillos, and the size and shape of the hole usually tells you which one. Fourth, trench settlement. The backfilled soil over a water line, a sewer line, or the utility feed was never compacted like the undisturbed ground beside it, so it keeps settling for years and leaves a sunken strip pointing at your house.

Each cause gets a different response. Erosion needs the water rerouted before any fill goes in. The shrinkage gap needs moisture management. A burrow needs the animal gone, then a compacted fill. A settled trench can simply be topped up and compacted, with one caution we will get to below. And if the hole is a chunk missing from the concrete at an outside corner under the brick, that is not a soil problem at all. It is [corner pop](https://motmotfoundationrepair.com/blog/what-is-corner-pop/), usually cosmetic, and it gets patched rather than filled.

## What animal digs holes around a house foundation?

In Central Texas the usual diggers are armadillos, Norway rats, pocket gophers and fire ants, with crawfish and cicada killer wasps showing up where the ground and the season suit them. You rarely see the animal. You see the hole, and the hole is a decent fingerprint. Measure the opening, look at what the dirt around it is doing, and match it in the table.

| What you see | What made it, and what to do |
| --- | --- |
| An open hole about 7 to 8 inches across, angled down under the slab edge, a porch, or the AC pad, often with small cone-shaped pokes in the lawn nearby | **Armadillo.** The pokes are feeding holes, 1 to 3 inches deep. Evict before you fill, then pack the burrow in thin layers. |
| A smooth, packed hole 2 to 4 inches across along the slab or under a stoop, with a worn path in the grass | **Norway rat.** Rats burrow beside foundations and under flatwork. Trap or exclude first, then fill and compact. |
| A fan-shaped mound of fresh soil with the hole plugged shut, or raised ridges running across the lawn | **Pocket gopher (the mound) or mole (the ridges).** Mostly a lawn problem. Collapsed runs near the slab get tamped and topped up. |
| A low dome of fluffy, crumbly soil with no opening on top, pushed up after a rain | **Fire ants.** Treat the mound, then rake it level once it goes quiet. No fill needed. |
| A small mud chimney of stacked pellets, an inch or two across | **Crawfish.** They only build where the ground stays wet, so next to a slab it is a drainage or leak clue. |
| Holes about half an inch across with a U-shaped spill of loose soil, in bare sunny ground in midsummer | **Cicada killer wasps.** They are gone by fall and do no harm to the house. Rake the spot and reseed after the season. |
| Pencil-wide mud tubes climbing the exposed slab edge | **Subterranean termites.** Not a hole at all. Call a licensed pest control company, and keep that slab edge visible so you see the next ones. |

None of these animals can move a foundation by themselves. What they do is loosen the soil at the edge and open a path for water to reach the clay under the slab. So the animal goes first. How to fill the run once it is empty is in the note on burrows further down.

## Piles of dirt around the foundation, and what made them

Piles of dirt around a foundation usually mean something is digging from below. In Central Texas that usually means fire ants, a pocket gopher, a rat or an armadillo, and a small mud chimney means crawfish and ground that stays wet. A spread of fine soil washing out from under the slab edge is a different signal, because water moved it. And sometimes the pile is the problem itself, dirt or mulch heaped up against the wall. Each one looks different and calls for a different fix.

### Fire ant mounds against the slab

A fire ant mound is a dome of loose, crumbly soil with no hole on top, and it often pops up after a rain. Fire ants like to build right against a slab, and some colonies nest under it. University extension guidance notes that they get into houses through cracks in the foundation, gaps at the slab edge and the weep holes in brick. A mound against the house does no structural harm by itself. Treat it with a bait or have a pest control company do it, rake it level once it goes quiet, and keep the slab edge visible so you catch the next one early.

### Pocket gopher mounds and mole hills

A pocket gopher pushes up a fan or horseshoe shaped pile of fresh soil, often 8 to 24 inches across, and plugs the hole on one side with dirt, so you never see an opening. That is how [Texas A&M AgriLife Extension](https://agrilifeextension.tamu.edu/controlling-pocket-gopher-damage) describes them, and a string of fresh mounds traces the tunnel underneath. Moles are different. The eastern mole, the only mole found in Texas, mostly leaves raised ridges just under the turf where it hunts insects. When a mole does push up a mound, it is rounder, shaped like a small volcano. Both are lawn problems first. Next to a slab the risk is the open tunnel, which gives rain a path down to the clay at the slab edge, so once the animal is gone, collapse the runs near the house and tamp them firm.

### Rat burrows under the slab edge

Norway rats dig burrows along foundation walls and under concrete slabs, stoops and walks. The sign is a smooth, packed hole with loose dirt pushed out in front of it and a worn path through the grass. Over time their digging can undermine the edge of a slab or a stoop, and a burrow that runs under the house gives water a ready channel to the clay. Trap or exclude the rats first, then fill the burrow in compacted layers like any other hole in this guide.

### Armadillo digging

Armadillo burrows are bigger. [AgriLife's armadillo guide](https://williamson.agrilife.org/files/2014/10/Armadillo.pdf) puts them at 7 or 8 inches across and up to 15 feet long, and notes that their burrowing has damaged foundations and driveways. Around a house they tend to angle under a slab edge, a porch or the AC pad, usually with shallow feeding holes poked across the lawn nearby. Get the armadillo out first, with a trap or a wildlife control company, then collapse and fill the burrow.

### Crawfish chimneys near the house

A crawfish chimney is a small tower of mud pellets stacked around a hole, built by crawfish that burrow down to wet ground. Extension services tie them to soil that stays saturated, from a high water table or poor drainage. Out in a low corner of the yard, a chimney is a drainage note. Right next to the slab in a dry spell, it means water is reaching that spot from somewhere, and a leaking line or a downspout dumping at the wall are the first things to check.

### Dirt washing out from under the slab

A spread of fine soil, silt or sand fanning out from under the slab edge or a stoop is the one pile no animal makes. Water moved it. After a hard rain it usually means runoff is running under the edge, often from a downspout or a low spot. If it shows up in dry weather, or keeps growing at the same spot, suspect a plumbing leak washing soil out from under the house. That is the time for the rod test in the section on voids below, and for asking a plumber to run a [hydrostatic test](https://motmotfoundationrepair.com/blog/hydrostatic-plumbing-test/) on the drain lines.

Soil gone from under the edge of a slab, with loose grit spread out in front of the opening. A spot like this gets checked for running water and for an animal before anyone fills it.

### Dirt piled up against the house

Sometimes the pile is the problem. Dirt, mulch or a raised flower bed heaped against the wall buries the slab edge, and the building code sets a minimum for how much of it must show. Section R404.1.6 of the International Residential Code asks for at least 4 inches of foundation above the finished grade where the wall has brick or stone veneer, and 6 inches elsewhere. Section R401.3 asks for the ground to fall at least 6 inches within the first 10 feet. Soil piled over that line holds water against the wall, blocks weep holes, and hides the termite mud tubes that a bare strip of concrete would show you. Pull it back, lower the grade if you have to, and slope it away. The slope check and how to rebuild a grade properly are covered further down, and the yard-wide picture is in [grading and drainage around a San Antonio foundation](https://motmotfoundationrepair.com/foundation-drainage-san-antonio/).

Ground cover planted tight against a stone veneer wall, with only a thin line of concrete showing below the stone. Soil and plants this high hold moisture at the wall and hide anything climbing it.

### Who to call about a pile of dirt by the foundation

Each kind of pile points to a different call. Ant mounds and rat burrows are a pest control job, and an armadillo is a job for a trap or a wildlife control company. A crawfish chimney beside the slab, soil washing out in dry weather, or a damp sunken strip over the sewer line is a plumbing question, and the hydrostatic test is where it starts. A pile of any kind that shows up with new cracks in the brick above it, doors that started sticking on that side, or a floor you can feel sloping is a foundation question. That is what our [free foundation inspection](https://motmotfoundationrepair.com/free-foundation-inspection/) is for, and about a third of the time it ends with no repair needed.

Soil eroded from a front entry slab edge. Roof water concentrated here for years before anyone noticed the hole.

## The right way to fill a hole next to a slab

The fill itself is honest weekend work, and here is the version that lasts. Use a clayey soil, not sand and not gravel. This comes straight from the engineering literature on expansive-soil sites. The [American Society of Civil Engineers (ASCE)](https://www.asce.org/) recommends filling depressions near the foundation with clayey soil, properly tamped, and warns that sandy soil is so permeable that water entering it can travel through the fill and wet the reactive clay underneath. A gravel-filled hole beside a slab works as a drain pointed at your foundation.

Dark native clay dug out beside a slab, the reactive soil most Central Texas houses sit on. Sand or gravel packed against it lets water straight through, so a hole here gets a firm clayey fill packed in thin layers.

Place the soil 4 to 6 inches at a time and compact each layer before adding the next. Crews call these layers lifts, and the guidance for backfill around foundations is thin lifts, tamped firm, rather than one deep pour of loose dirt. Before the first lift goes in, pull out leaves and loose debris and rough up the bottom of the hole so the new soil bonds to it. The fill should be damp, not wet. Squeeze a handful and it should hold a ball that crumbles when you poke it. Bone-dry clods will not pack, and mud squeezes out sideways under the tamper. A hand tamper, a piece of 4x4, or your boot heel on a small hole all work. Loose fill can lose a third of its volume as it settles, which is why the hole you filled in March is back by July. Overfill slightly, mound the last lift an inch or two proud, and let it settle flush. The same settling, at a much bigger scale, is what happens when a builder levels a slope with placed fill, which is why [houses on cut and fill lots](https://motmotfoundationrepair.com/blog/cut-and-fill-lot-foundation-problems/) tend to crack on the filled side first.

Then grade it. The finished surface should slope away from the house on every side, steadily, for at least the first several feet. The same guidance calls this positive drainage and ranks it among the most valuable things an owner can do for a house on expansive clay. Walk the perimeter after the next hard rain and look for anywhere water stands within about five feet of the slab. Standing water next to the foundation soaks in, swells the clay, and lifts that edge. One more detail. Do not build the finished soil up against the wall. Leave at least 4 inches of concrete showing below brick and 6 inches below siding, so the weep holes stay open and termites have to cross bare concrete where you can see them. What those little gaps in the mortar do, and why they must stay open, is covered in [what are weep holes in brick](https://motmotfoundationrepair.com/blog/what-are-weep-holes-in-brick/).

Erosion exposing a porch slab edge. Before this gets filled, the water that carved it has to be rerouted.

## Should you fill it with concrete, gravel, or foam instead?

Not in the dirt beside a slab. Forum answers suggest gravel topped with concrete, a bag of quick-set, or a can of expanding foam, and each one sets up the next problem. Concrete poured into a soil hole becomes a rigid plug in ground that swells and shrinks around it. The clay pulls away from the plug in a dry spell, rain finds the seam, and the water runs down the side of the plug to the slab edge. The plug also hides the hole without explaining it, and if anyone ever needs to dig there for a pier or a plumbing repair, it has to be broken out first. Gravel is the drain we warned about above. Expanding foam from a can does not compact, breaks down in sunlight, and gives termites a hidden path to the wall.

Concrete belongs where the hole is in the concrete. A chipped slab corner or a spall at the edge gets a patching mortar once you know the movement behind it has stopped. A crack in the slab itself is a different decision, and [retail crack sealers](https://motmotfoundationrepair.com/blog/diy-foundation-crack-sealers/) do one job well, which is keeping water out of concrete that has stopped moving. A void under a sidewalk or a porch slab is the one place where pumped material makes sense, and we get to that below.

## How much fill dirt to buy, and the tools to pack it

Measure the hole in feet. Length times width times depth gives cubic feet, and dividing by 27 turns that into cubic yards, which is how bulk soil is sold. Then add a quarter to a third for compaction, because loose soil packs down when you tamp it. A hole two feet square and a foot deep is 4 cubic feet, so plan on 5 to 6. Bagged soil is labeled by volume, often three quarters of a cubic foot per bag, so that hole takes seven or eight bags. Building up a 30-foot run of wall by an average of 4 inches over a strip 4 feet wide is 40 cubic feet, or 50 to 53 once you allow for compaction, about two cubic yards. Past a yard or so, bulk fill delivered by a landscape supplier is usually easier than hauling bags. Ask for clay fill or select fill rather than sandy loam, and save the topsoil for the top few inches where grass has to grow.

The tools are simple. A flat shovel and a hard rake move and spread the soil. A hand tamper, which is a square steel plate on a handle, does the compacting on anything smaller than a flower bed. A hose with a mist nozzle dampens dry fill before you tamp it. A straight 10-foot board and a level check the slope when you are done. For a long run of fill, rent a jumping-jack rammer, but call 811 first and hand-tamp the first foot of soil over any buried line. The vibrating plate compactors on the same rental shelf are built for sand and gravel, and on clay they mostly bounce.

A backfilled excavation under bay windows. Fresh fill keeps settling for a few rains, and the soil heaped at the wall still has to be spread out and sloped away from the house.

## How much should the ground slope away from the foundation?

The building code gives a number. Section R401.3 of the International Residential Code, which most Central Texas cities adopt, asks for the ground to fall at least 6 inches within the first 10 feet from the foundation. That is a 5 percent slope, a little over half an inch per foot. Paved surfaces next to the house, like a patio or a walk, need at least a 2 percent fall away from the wall. Engineering guidance for expansive soils lands in the same place, and it warns that anything flatter lets water sit in shallow low spots and soak in instead of running off.

Checking it takes ten minutes. Rest one end of a straight 10-foot board on the soil at the foundation, pointing straight out from the wall. Put a level on the board, raise the far end until the bubble centers, and measure from the bottom of the board down to the soil. Six inches or more and you are fine. Less than that means the slope is too flat, and a gap that is bigger in the middle than at the far end means a dip that will hold water. A string line on two stakes with a line level does the same job over a longer run.

Plenty of side yards are not 10 feet wide, and the code allows for that. Where a fence, a wall, or the neighbor's house gets in the way, the water has to be carried off by a swale, which is a shallow graded channel, or by a drain. The slope, gutters and swales that make the rest of the yard drain are covered in [grading and drainage around a San Antonio foundation](https://motmotfoundationrepair.com/foundation-drainage-san-antonio/).

Water standing against the slab after every rain? The drainage review is part of the free inspection across our ten Central Texas counties.[Book a Free Inspection](https://motmotfoundationrepair.com/#inspection-form)

## How to build up soil around a house foundation

To build up soil around a house foundation, place clay fill in 4 to 6 inch layers, tamp each one firm, finish with 2 to 4 inches of topsoil, and slope the surface away from the wall without burying the slab edge. When the yard has sunk or washed away along a wall, building it back up follows the same rules as filling a hole, only bigger. The clay fill does the bulk of the work, and the topsoil is there so grass or plants have something to root in. Do not use topsoil for the deep part. It is full of organic matter that breaks down over time, and the grade sinks with it. If the low strip along your wall is backfill from earlier foundation work, give it a few months and a couple of top-ups before you regrade, because [backfill around new piers](https://motmotfoundationrepair.com/blog/foundation-repair-and-landscaping/) keeps settling for a season before it sits flush.

The limit is the wall. The code wants at least 4 inches of foundation showing above the finished grade under brick and 6 inches elsewhere, and wood siding or trim needs 6 inches of clearance from the soil. If raising the grade enough to get your slope would bury that line, take soil away farther out or add a swale. Never pile dirt higher against the house. Mulch counts as soil here too. Pull it back from the slab and keep the edge visible, because the bare concrete strip is where termite mud tubes show up first, and our guide to [telling wood rot from termite damage](https://motmotfoundationrepair.com/blog/wood-rot-vs-termite-damage/) covers what to look for if they do.

Flower beds are where most of this goes wrong. A bed dug below the lawn and closed in with edging holds water against the slab like a bathtub, and watering by flooding the bed does the same thing. Keep beds level with the lawn or slightly above it, sloped away from the wall and still below that clearance line, and water them with drip or a soaker hose. Keep big trees back as well. A large shade tree belongs at least its mature height from the slab, and the [tree distance guide for Central Texas foundations](https://motmotfoundationrepair.com/blog/tree-planting-distance-foundations/) lists what each common species needs.

A backfilled strip along a brick wall. Disturbed soil like this keeps settling for months, so it gets topped up and re-sloped after the first few hard rains.

## A note on burrows and trench lines

Animal holes get the same treatment with one extra step. Evict first. Filling an occupied burrow just commissions a new one a few feet down the wall, usually by morning. Once the tenant is gone, collapse the run as deep as you can reach, then fill and compact in lifts like any other hole. Trench settlement is the more patient case. The soil that went back over your water, sewer, and utility lines was rarely compacted like the undisturbed ground beside it, so it keeps consolidating for years, leaving a tidy sunken stripe aimed at the house. That is why, when we close a plumbing tunnel or trench, [the backfill goes back in compacted lifts](https://motmotfoundationrepair.com/under-slab-tunneling/tunnel-backfill-cleanup/) instead of as loose spoil. Top a settled trench up, compact it, slope it, and then keep an eye on it. A trench line that keeps sinking, or that stays damp when the surrounding yard is dry, has stopped being a compaction story and started being a plumbing question.

An access tunnel dug under a slab edge. When the work is done it gets backfilled and compacted in layers. Skip that and the ground above turns into a sunken stripe.

Before you dig into a trench line to re-compact it, or dig anything deeper than a few inches near the house, call 811. In Texas the free [Texas811](https://texas811.org/) service needs two working days' notice to mark the lines, and state rules make the call mandatory for digging deeper than 16 inches. Gas and electric service lines are often shallow right where they enter the house, which is exactly where these holes like to appear. Outside Texas, 811 works the same way in every state.

Backfill being worked into a completed excavation. The soil goes back in layers, tamped as it goes, and mounded to settle flush.

## The summer gap between soil and slab is not a hole

The most misunderstood opening around a Texas foundation is the shrinkage gap. The Blackland clays under the San Antonio and Austin corridor, with [Houston Black](https://soilseries.sc.egov.usda.gov/OSD_Docs/H/HOUSTON_BLACK.html) as the USDA's textbook example, are among the most reactive soils in the country. In a drought they shrink hard, and the ground visibly pulls away from the slab edge. Homeowners see the gap, buy a few bags of sand, and pack it in. Then the rains come, the clay swells back, and the sand has nowhere to go except to hold the gap open and channel the next rain straight down the slab edge. How to read that gap before you do anything to it, and when it points to the house rather than the weather, is in [soil pulling away from the foundation](https://motmotfoundationrepair.com/blog/soil-pulling-away-from-foundation/). Why some clays react so much harder than others is a lab question, and [what is the plasticity index of soil](https://motmotfoundationrepair.com/blog/what-is-the-plasticity-index-of-soil/) answers it in plain terms.

The right move is moisture, applied correctly. Lay a soaker hose about eighteen inches out from the slab and run it on a steady schedule so the perimeter clay stays evenly damp instead of swinging between soaked and bone dry. Two warnings from the engineering guidance are worth following exactly. Start early in the dry season, before the ground cracks open. And never pour water directly into a crack or gap beside the foundation, because it runs straight down, ponds under the slab edge, and heaves the corner you were trying to protect. We cover the mechanics in [why drought causes foundation damage](https://motmotfoundationrepair.com/blog/why-drought-causes-foundation-damage/) and the overcorrection in [the consequences of over-watering](https://motmotfoundationrepair.com/foundation-watering/).

How hard your ground swings depends on how much clay it holds and what kind. Our [foundation risk map](https://motmotfoundationrepair.com/foundation-risk-map/) scores any US ZIP code from USDA shrink-swell data, so you can check your own soil wherever you live. Closer to home, we ranked [every San Antonio ZIP code](https://motmotfoundationrepair.com/blog/san-antonio-zip-codes-foundation-problems/) and [the Austin ZIP codes](https://motmotfoundationrepair.com/blog/austin-zip-codes-foundation-problems/) by the soil under them.

A finished corner graded to shed water away from the house. The slope is the part of the job that keeps the hole from coming back.

## When the hole is really a drainage problem

A hole that keeps reappearing in the same spot is not a filling problem. It is a plumbing diagram written in dirt. Follow it uphill and you will usually find a downspout discharging at the slab, a gutter that overflows at one low corner, or a neighbor's runoff crossing your foundation line. On a hillside lot, storm runoff hits the uphill wall first every time, and [why houses on sloped lots move the way they do](https://motmotfoundationrepair.com/blog/sloped-lot-foundation-problems/) has its own guide. Fill the hole all you want, and the next storm re-excavates it. The fix is the boring one. Clean gutters, [downspout extensions that discharge at least six feet from the slab](https://motmotfoundationrepair.com/blog/downspout-distance-foundation/), and regrading so the water has somewhere better to be. That work is genuinely yours to do, and our guide to [what you can DIY on a foundation](https://motmotfoundationrepair.com/blog/can-i-repair-a-foundation-myself/) puts it at the top of the list.

A dark water streak down a stucco corner, with wet leaves and soil collected at its base. Water that keeps arriving at the same spot is what carves a hole there, so it gets traced before anything is filled.

When the water problem outgrows a hose extension, that is [drainage correction](https://motmotfoundationrepair.com/drainage-correction/), meaning regrading, [french drains](https://motmotfoundationrepair.com/french-drain-installation/) or area drains, scoped from the same measured inspection as everything else we do. Many of those fixes cost a fraction of what foundation work does, and they end the hole-filling ritual for good. Not sure which one you have? [Telling a drainage problem from a foundation problem](https://motmotfoundationrepair.com/blog/foundation-repair-vs-drainage-correction/) is its own guide. The slower version of this failure, where poor drainage quietly works on the slab for years, is laid out in [how poor drainage damages slab foundations](https://motmotfoundationrepair.com/blog/how-poor-drainage-damages-slab-foundations/).

## Holes around a pier and beam house

On a raised house the holes show up along the skirting, and they almost always mean something moved in underneath. Skunks, armadillos and opossums treat a crawl space as a den, and a skirt that ends at the soil line is easy to dig under. Get the animal out first, with a one-way door or a wildlife control company, then fill the dug-out runs with compacted soil and slope them away like any other hole. What keeps them out for good is a buried hardware-cloth apron along the bottom of the skirt, and our guide to [skirting options for pier and beam homes](https://motmotfoundationrepair.com/blog/skirting-options-for-pier-and-beam-homes/) covers how that goes in.

Inside the crawl space, do not fill between the piers. People ask about this when they see low spots or puddles under the house, and the instinct is to shovel dirt in. That space is there on purpose. The code expects at least 18 inches between the soil and the bottom of untreated floor joists and 12 inches to the beams, and a crawl space only stays dry when air moves through it. Dirt piled between the footings closes that gap, buries the vents, puts damp soil against wood, and gives termites a bridge. Low spots under a raised house that hold water after rain are a grading problem outside the skirt, and [crawl space moisture control](https://motmotfoundationrepair.com/crawl-space-moisture-control/) covers that side of it.

### What fill goes between foundation footings?

On a new slab, the space inside the grade beams gets select fill, a low-plasticity clayey soil placed in thin lifts and compacted before the slab is poured. On an existing [pier and beam house](https://motmotfoundationrepair.com/pier-beam-foundation-repair/), nothing goes between the footings. The open crawl space is what keeps the floor framing dry. If you are not sure which kind your house has, [pier and beam vs slab](https://motmotfoundationrepair.com/blog/pier-and-beam-vs-slab-foundations/) shows how to tell.

## Voids under a slab, porch, or sidewalk

A hole that runs sideways under concrete is a void, and it needs a different approach. Two quick checks tell you what you have. Push a steel rod or a long screwdriver horizontally under the edge of the slab and feel for open space. Then tap the concrete with a hammer, working in from the edge. Solid concrete gives a sharp click. Concrete over a void sounds hollow, like a drum, and the hollow area traces the size of the void.

A hole opening under the corner of a porch slab beside the brick. A run that heads under concrete gets the rod test before anyone fills it.

Under a porch, a sidewalk, a patio, or a driveway, a void is a flatwork problem. Those slabs usually sit on their own, separate from the house foundation, and the standard fixes are pumping a cement slurry underneath, called mudjacking, or injecting expanding polyurethane foam. Our guides cover [what mudjacking costs and what it can lift](https://motmotfoundationrepair.com/blog/how-much-does-mudjacking-cost/) and [the pros and cons of polyurethane foam](https://motmotfoundationrepair.com/blog/polyurethane-foam-foundation-repair/). Neither one lifts a house. When the porch itself is dropping or pulling away from the wall, start with [why a porch pulls away from the house](https://motmotfoundationrepair.com/blog/porch-pulling-away-from-house/).

Pumped material only holds if the soil under it has finished moving. On clay that is still swelling and shrinking, a leveled walk can drop again within a few seasons, and [concrete leveling on San Antonio clay](https://motmotfoundationrepair.com/blog/concrete-leveling-san-antonio/) explains how to tell which kind of ground you have before you pay for a lift.

Under the house itself, a void matters more, and it gets measured before anyone fills it. Soil does not leave from under a slab on its own. Moving water carries it, either surface water running under the edge or a plumbing leak washing it out from inside. So the first step is finding the water. A [hydrostatic plumbing test](https://motmotfoundationrepair.com/blog/hydrostatic-plumbing-test/) tells you whether the drain lines under the slab are leaking. A pipe that split in a hard freeze can keep leaking long after the thaw, so a new soft spot after a cold snap deserves the same test, and our piece on [freeze damage to Texas foundations](https://motmotfoundationrepair.com/blog/freeze-foundation-damage-texas/) walks through that chain. A leak can also do the opposite of a void. Clay that soaks up leak water swells and pushes the slab up, and [leak heave](https://motmotfoundationrepair.com/blog/leak-heave-explained/) is easy to mistake for settlement.

Do not pump anything under a house slab yourself. The pressure that lifts a sidewalk can raise a section of floor that never needed raising, and it buries the evidence of where the water came from. When the leak is under the slab, a licensed master plumber does the plumbing work. Our part is the tunnel or access opening that reaches the pipe, and the compacted backfill afterward, and [what an under-slab tunnel costs](https://motmotfoundationrepair.com/blog/under-slab-tunneling-cost/) depends mostly on how far the crew has to dig and what the soil is like.

A void under the slab, a damp sunken strip over the sewer line, or a hole that showed up with new cracks? Those are inspection questions, and in our service area the inspection is free.[Book a Free Inspection](https://motmotfoundationrepair.com/#inspection-form)

## When a hole means the foundation is the problem

A few holes are symptoms, and these are the ones worth a professional's eyes before you fill them. A void that runs back under the slab, where you can push a rod horizontally and feel open space beneath the concrete, means soil has been removed from under the foundation, usually by moving water and sometimes by a [plumbing leak under the slab](https://motmotfoundationrepair.com/blog/plumbing-leaks-under-slab/). A leak makes the same shapes on the surface, a sunken strip over the sewer line, a hole that stays damp in dry weather, or ground that is soft when everything around it is baked hard. And any hole that shows up alongside signs of movement, fresh stair-step cracks in the brick above it, doors sticking on that side of the house, a slope you can feel underfoot, has stopped being a landscaping item. When the hole, the cracks and the sticking door all sit at one corner, read [what a single sinking corner usually means](https://motmotfoundationrepair.com/blog/one-corner-of-house-sinking/) before anyone quotes a whole-house repair.

Filling a symptom hole does not hurt anything, but it hides the evidence and buys the real problem another season. This is the moment for a free inspection, with a floor elevation survey read in tenths of an inch, the cracks mapped and photographed, and the drainage reviewed. About a third of the time there is no repair to recommend, and if yours lands there, you fill the hole with a clear conscience and [a simple way to monitor the cracks yourself](https://motmotfoundationrepair.com/blog/monitor-foundation-crack/). What we will not do is turn a downspout hole into a pier quote. If it is dirt and water, we say so.

We inspect homes in Bexar, Travis, Williamson, Hays, Comal, Guadalupe, Kendall, Medina, Bastrop and Caldwell counties, and in that area the inspection is free. Book it below or call [(210) 816-0034](tel:+12108160034). If you are reading this from somewhere else, everything above about clay, lifts, slope and water still applies to your house. When you call someone local, pick an inspector who measures floor elevations before talking about piers, and be wary of anyone who quotes a foundation repair for a hole that turns out to be a downspout.

A hole that keeps coming back, or one that showed up with new cracks? The inspection that sorts dirt from movement is free across our ten Central Texas counties.[Book a Free Inspection](https://motmotfoundationrepair.com/#inspection-form)

---

Source: https://motmotfoundationrepair.com/blog/how-to-fill-holes-around-house-foundation/
Summary: How to fill holes around a house foundation. Find the cause, pack clayey fill in 4 to 6 inch layers, and slope it 6 inches in 10 feet.
Motmot Foundation Repair, San Antonio, Texas. (210) 816-0034. https://motmotfoundationrepair.com/
