Learning Center · Crawl Spaces

What Causes Condensation in a Crawl Space?

View as Markdown

WHERE SUMMER CONDENSATION FORMS UNDER A RAISED FLOOR

SurfaceWhy it sweatsWho fixes it
AC supply ductsAir leaving the coil runs in the 50s. Torn jackets, loose joints and bare register boots drip whenever the crawl space air is muggy.HVAC contractor
Subfloor under cooled roomsA low thermostat chills the floor from above. On muggy days the underside soaks up crawl space moisture, and wood floors cup.Thermostat habits, then HVAC
Cold water linesSupply pipes can bead up on the muggiest days. Usually minor.You, with foam pipe insulation
Insulation between joistsBatts soak up the drips, sag out of the bays and hold water against the wood.Insulation contractor
Ducts and floors sweat here because the air conditioner made them cold, which is why crawl space condensation in Central Texas is a summer event.

What causes condensation in a crawl space? Warm, humid air touching a surface that is colder than the air's dew point. The water comes out of the air as droplets, the same way a glass of iced tea sweats on a July porch. Under a Central Texas house, the cold surface is usually something the air conditioner chilled, like the supply ductwork or the subfloor under rooms kept cool, and now and then a cold water line during a muggy stretch. Condensation is the exception here, though. Most water we find under raised floors arrives as liquid, from grading, downspouts or a leak, so prove which one you have before you pay for a fix.

Decayed subfloor pieces and debris on crawl space soil around a loose white PVC drain pipe
Decayed subfloor pieces and debris on the soil under a raised floor, beside a loose length of drain pipe. Damage this far along had a steady water supply, and the first question is whether it came from a leak or from summer condensation.

How condensation forms, in plain terms

Air always carries some water as invisible vapor. The dew point is the temperature at which that air would be holding all the water it can. Cool air down to its dew point and the extra water condenses out. A cold surface does that cooling for the thin layer of air touching it, so water beads on the surface while the rest of the crawl space stays clear.

Relative humidity is the number most people know, and it shifts with temperature. Air at 90 degrees and 60 percent relative humidity outside reads above 80 percent once it settles under the house at 80 degrees, with no water added. For condensation, the dew point is the number that counts. If it is higher than the temperature of a surface, that surface gets wet. If it is lower, nothing condenses, however sticky the day feels.

The National Weather Service office for Austin and San Antonio lists the dew point with every hourly observation. When Gulf moisture settles over the region in summer it often sits around 70 degrees, and higher on the muggiest days. Air leaving an air conditioner runs in the 50s, and that gap is where the trouble starts.

Where condensation shows up under a raised floor

Supply ducts. Sweating ductwork in a crawl space is the most common case. Flex duct and duct board carry insulation behind a vapor-tight outer jacket for exactly this reason. Where the jacket is torn, a joint has pulled apart, or the insulation has slid back from a register boot, cold duct meets humid air and drips. A leaky joint does double damage, because it blows chilled air across the joists around it and makes them cold enough to sweat too.

The subfloor under cooled rooms. In summer the house is the cold side of the floor. Hold the thermostat at 68 and the subfloor runs cooler than the crawl space air. Where fiberglass batts fill the joist bays, it sits close to room temperature, because the insulation keeps the crawl space heat off the wood while humid air seeps right through. On the muggiest nights the crawl space dew point can climb into the low 70s. Even when no water beads, the underside of the floor soaks up moisture. Wood floors show it first. The boards cup because the bottom of each board takes on water the top never sees. Under carpet or vinyl you may see nothing until the floor feels soft or smells musty. That is what most people mean by sweating floors on a pier and beam house.

Cold water lines. Supply pipes can bead up on the muggiest days. Foam pipe insulation from the hardware store, with the seams taped shut, usually ends it. The AC condensate line belongs here too, though what it carries is liquid water the coil pulled out of your indoor air. When it is disconnected, cracked or ends under the house, it waters the same patch of soil all summer, and the puddle gets blamed on humidity.

Wet insulation. Fiberglass batts between the joists soak up drips, sag out of the bays and hold water against the wood for days after the weather breaks. Batts hanging loose or lying on the soil usually mean something above them has been dripping.

PVC drain lines hung on metal straps under floor framing, with blue and red water supply lines running beside them
Drain lines on metal strapping under a raised floor, with blue cold and red hot water lines beside them. Of these pipes only the cold line runs cold enough to bead up on a muggy day, so water dripping from the drains points to a leak.

Why crawl space condensation is a summer problem in Central Texas

In cold climates, condensation under a house is a winter problem, because warm, moist air from the living space reaches framing chilled by the outdoor cold. Central Texas runs the other way. Our winters are mild, hard freezes are rare, and frost barely reaches into the ground. The fronts that bring our cold weather usually carry dry continental air, and the heating system keeps the floor and the ducts warm from above. On most winter days the crawl space has nothing cold enough for its air to condense on.

Summer flips the floor. The air conditioner makes the house the cold side, Gulf moisture makes the outside air the wet side, and the ducts and subfloor sit right between them. Even then it comes in spells, during muggy weeks rather than all season. As our crawl space moisture control page puts it, liquid water does most of the harm under houses here, and the muggy stretch is the occasional exception.

There is one winter footnote. After a hard freeze, the first warm, humid day can make cold-soaked piers and pipes sweat for a day or two, and that dries on its own. A pipe that split in the freeze does not. Winter Storm Uri in February 2021 soaked plenty of Central Texas crawl spaces through burst supply lines, and that water was a leak. After a hard freeze, check the plumbing before you blame the weather, and read freeze damage to Texas foundations.

Wet soil under the duct runs, or a wood floor that started cupping this summer? The free inspection goes under the house to find where the water is coming from, across our ten Central Texas counties.Book a Free Inspection

Is it condensation or a leak?

Answer this first, because the two fixes have nothing in common.

Timing. Condensation follows the weather and the air conditioner. It shows up in muggy spells, peaks in the afternoons and evenings when the AC runs hardest, and dries out when a dry front comes through or fall arrives. A leak ignores the weather. It stays wet in October, wets the soil in January, and often gets worse right after someone showers or runs the laundry or the dishwasher.

Location. Condensation follows the duct runs and register boots, so it leaves a string of drip marks along them. A supply leak makes one wet spot that keeps growing, usually under a bathroom, the kitchen, the laundry or the water heater. A drain leak stains the soil under a fixture or along a sloped pipe, and it often smells like sewage rather than damp earth.

The water meter. Turn off every faucet, the ice maker and the irrigation, then watch the small leak indicator on your water meter for fifteen minutes. If it moves with everything off, water is going somewhere, and a licensed plumber should find it. The meter only tests the supply side, since drain lines leak only when water runs down them. Liquid water gets its own guide in why there is water in your crawl space.

Decayed wood and debris around a white PVC drain line beneath a pier and beam floor
Decayed wood and fallen subfloor around the drain plumbing beneath a floor. Rot clustered along pipes points to a plumbing leak first, while condensation damage tends to follow the duct runs.

Either way, a pin-type moisture meter pushed into the wood shows how far it has gone. Sound framing under a house usually reads somewhere in the teens, a little higher in a muggy August. Readings at 20 percent and up mean the wood is staying wet long enough to matter.

What humidity should a crawl space be?

There is no code number for a vented crawl space, so measure your own. Set a digital hygrometer that records the daily high and low on a block just inside the crawl space access, and a second one outside in the shade. Read both through a muggy week and again after a dry front. If you do crawl farther in, wear gloves and a mask, watch for wiring and critters, and stay out if there is standing water or a sewage smell.

The EPA's guide to mold, moisture and your home says to keep indoor humidity below 60 percent, ideally between 30 and 50. A vented crawl space will not hold that in a Central Texas summer, and it does not need to. On a summer afternoon the crawl space runs cooler than the yard, so its relative humidity reads higher with no water added. Compare dew points instead, which many hygrometers display. A crawl space dew point close to the outdoor one is just the weather. One that runs higher than outdoors means the extra water is coming from inside the crawl space, from damp soil, a leak or a condensate line.

The wood is what you are really protecting. The USDA Forest Products Laboratory's Wood Handbook explains how framing takes on or gives up water until it matches the air around it. It also says humid air by itself will not wet wood enough for serious decay, though it can let some mold grow. Rot needs liquid water from rain, condensation or wet ground, and wood kept at about 20 percent moisture content or below has a reasonable margin of safety. Under a house that liquid water arrives as drips off a sweating duct, a leak, or a soaked batt pressed against a joist.

Mold in the crawl space

Mold in a crawl space needs moisture, something to feed on and time, and joists that stay damp through a muggy summer supply all of it. It shows up as fuzzy white, gray or black growth on the joists and the underside of the subfloor, heaviest where the drips land along the duct runs. White powder on concrete piers is usually efflorescence instead, mineral salts that water carried out of the concrete.

There is no practical way to get rid of every mold spore indoors, so the EPA's approach is to control the water mold grows on. Fix the moisture problem first, then clean or remove what grew. The EPA says a homeowner can usually handle an area smaller than about 10 square feet. Past that, it points to its professional remediation guidance.

Motmot does not do mold remediation. In Texas, mold assessment and remediation are licensed by the Texas Department of Licensing and Regulation. Our part comes after, when the wood under the mold has lost strength. Wet wood loses stiffness long before it rots, which is one of the reasons behind bouncy floors over a damp crawl space. Damp framing draws termites as well as rot, and wood rot vs termite damage shows how to tell them apart.

Gap opening between a plank floor and a wood-paneled wall beside a wall grille
A gap opening between a plank floor and a paneled wall. When the framing under a room stays damp and sags, a gap like this is one way it shows up in the room above.

How to stop condensation in a crawl space

Work in this order, because each step changes whether you need the next one.

First, stop the liquid water. That means soil that slopes away from the house, downspouts that discharge well out from the skirting, a repaired supply or drain leak, and a condensate line that ends outside. It is the most common source of water under Central Texas houses. The grading and drainage side of this is work we do.

Open joint packed with dead leaves along the weathered sill line behind aging skirting
An open joint at the sill line behind aging skirting, packed with dead leaves. Gaps like this let rain in as liquid water, and that gets fixed before anyone works on humidity.

Second, cover damp soil. The Wood Handbook names soil moisture as the main source of condensation on crawl space framing, and a polyethylene sheet laid over the soil as the way to isolate it. Never lay plastic over standing water, which only hides the problem. Whether your house needs one at all is covered in do you need a vapor barrier in a crawl space.

Third, seal and insulate the ducts. The Department of Energy's Energy Saver guide says ducts leaking into a crawl space can add hundreds of dollars a year to heating and cooling bills, calls sealing and insulating ducts in unconditioned spaces usually very cost effective, and recommends a qualified professional for duct repairs. A licensed HVAC contractor can seal the joints, replace torn jackets, close the gaps at register boots, and confirm the condensate line ends where it should.

Fourth, watch the thermostat. A colder setting chills the subfloor further and keeps the ducts running cold for more hours of the day. Holding the house at 68 during a muggy week is asking the floor to sweat. A few degrees warmer with ceiling fans running narrows that gap.

Last, think about the vents. Here they stay open most of the year, because open vents dry the crawl space after rain, a leak or a downspout failure. During a muggy stretch, when your hygrometers show the outdoor air wetter than the crawl space, closing them for a few days is reasonable. The full reasoning is in should crawl space vents be open or closed.

Encapsulation, a sealed liner with a dehumidifier, does stop condensation when it is done right, and in the humid Southeast it often makes sense. Here it is usually more than a house needs once the steps above are done. We do not sell encapsulation or dehumidifiers, so read is crawl space encapsulation worth it in Texas before you sign for one.

What we do under the house, and who does the rest

We are a foundation company. Under a pier and beam house our work is the piers, beams, shims and leveling, the repair of sills and joists that moisture has softened, and the drainage correction and regrading that keep water away from the house. That structural half is pier and beam foundation repair. Duct sealing and AC sizing belong to a licensed HVAC contractor. Pipe leaks belong to a licensed plumber. Insulation belongs to an insulation contractor, and mold to a licensed remediator. If the only problem under your house is a torn duct jacket, that is what we will tell you.

The free inspection on a pier and beam home includes going under the house. We read damp soil, standing water and grading, note where every downspout discharges, and take floor elevations. About a third of our inspections end with no repair needed. The inspection is free in Bexar, Travis, Williamson, Hays, Comal, Guadalupe, Kendall, Medina, Bastrop and Caldwell counties. Book it below or call (210) 816-0034.

Sweating ducts, a musty summer smell, or soft spots in the floor? The inspection that sorts condensation from a leak and from real framing damage is free across our ten Central Texas counties.Book a Free Inspection

Straight answers

Related questions.

Floors sweat when the floor surface is colder than the dew point of the air touching it. On a raised house in summer that usually happens underneath, where muggy crawl space air meets a subfloor chilled by the air conditioning, and wood floors answer by cupping. Water beading on top of a floor is a different case. That is humid indoor air landing on cool tile or a cool slab, common when windows are open on a muggy day or when warm, wet air arrives right after a cold snap. Find the humidity source, and keep the thermostat from running the floor colder than it needs to be.
There is no code number for a vented crawl space. The EPA's guidance for indoor air is below 60 percent, ideally 30 to 50 percent, and a vented crawl space in a Central Texas summer will read higher than that on muggy days, which is normal. What matters is the trend and the wood. Humid air by itself will not wet wood enough to rot it, and framing at about 20 percent moisture content or below has a reasonable margin of safety, so readings above that usually mean liquid water is reaching the wood. Compare the crawl space dew point with the outdoor dew point. If the crawl space runs wetter, the extra water is coming from damp soil, a leak, or a condensate line.
It can. Mold needs moisture and something to feed on, and joists and subfloor that stay damp through a long muggy summer supply both. It usually starts where the drips land, along the duct runs and around the register boots. The EPA's rule is to fix the moisture first and then clean or remove what grew. It says a homeowner can usually handle a patch smaller than about 10 square feet, and that larger growth calls for its professional remediation guidance. Motmot does not remediate mold. Our part comes afterward, when the wood under the mold has lost strength and needs framing repair.
Not as a year-round fix in Central Texas. Open vents are what dry a crawl space after rain, a leak, or a downspout failure, and most water under houses here arrives as liquid. During a muggy stretch, when a hygrometer shows the outdoor air is wetter than the crawl space, closing them for a few days is reasonable. Open them again when the weather breaks, and close them on hard-freeze nights to protect the pipes. Sealing the ducts and stopping the liquid water will do far more than the vents ever will.
Yes, slowly. Wet wood loses stiffness long before it rots, so a floor over a damp crawl space can feel bouncier before any decay shows. Framing that stays above about 20 percent moisture content season after season invites rot and termites, and the sill plates and joist ends closest to the soil go first. Once a screwdriver sinks into the wood, it needs repair or replacement, because drying it out does not bring the strength back. Stop the moisture first, or the new wood follows the old wood down.

Wondering about your own house?

A free elevation survey answers in an hour what an article can only describe, and 'you're fine' is a real possible outcome.

Now booking free inspections in Central Texas.

Free inspection request

Tell us what you're seeing.

We'll call to schedule, usually within one business day. Prefer to talk now? (210) 816-0034.

  • 60–90 minutes on site, including the elevation survey
  • Written summary whether or not repair is needed
  • No-pressure pricing with firm numbers, no same-day-only discounts

Name and phone are all we need. Everything else just helps us come prepared.

By submitting, you agree to our Privacy Policy and Terms, and consent to be contacted by Motmot Foundation Repair by phone or email about your request. Consent to texts is not a condition of purchase. See our SMS Terms.

Google reviews

What our customers say about the work.

Drainage issues hurt my foundation, but Motmot Foundation Repair helped me fix my slab porch and pier and beam foundation and also installed a French Drain. What a dependable también. Thank you

Antonio Contreras5 months agoGoogle

We started noticing cracks in the garage area of the home. Found Motmot on google and reached out for an estimate. They were so quick to respond and were able to schedule a visit right away. (At our convenience) Ricardo arrived right on time ! He evaluated our entire home and gave us an explanation and honest assessment. He was extremely courteous and thorough. Will hire them when we're ready to move forward. It's so refreshing to find a company that does what they advertise!

Cindy Thurn10 weeks agoGoogle
Reviews from Google. We display them exactly as written.

Read our sponsored article in MySA, Before You Spend Thousands on Foundation Repairs. We are also a member of the National Foundation Repair Association.